Just How to Replace a Tub

Explore Now

Were you in search of help and advice around How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?


Tools You Need to Install a New Bathtub
Mounting a bathtub isn't precisely brain surgery, yet it does require solid plumbing, carpentry, and also sometimes, tiling skills. Replacing an old tub with a brand-new one is additionally a reasonably difficult job. If the old bathtub is conveniently obtainable, the task can move quickly; if you have to open up a wall surface to get rid of the old tub and position the brand-new bath tub, the job is a lot harder. In either case, the project is within a house handyman's skills, although you will certainly require an assistant to vacate the old bathtub and set in the new one. Ensure you have qualified yourself for the task as well as are comfortable trying it. Instead of working with a specialist to take over a halfway-completed job, it is much better to think about utilizing one before you begin. Possibilities are you may need an expert plumber to make tube connections.
This short article will assist you set up a new bathtub in your restroom if you have currently bought a brand-new bathtub and also do not require to alter the plan of your previous water system pipes.
Your tools and also product list ought to comprise the following:
  • New Bath tub
  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Shatterproof glass

  • Level

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Knife

  • Measuring tape

  • Pipeline Caps


  • Getting ready for the Installation


    Firstly, the sustaining framework supplied with the bath needs to be fitted (if called for) according to the supplier's directions. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is essential to make sure that if the faucet features a plastic washing machine, it is fitted in between the bath and the faucets. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the faucets unit to prevent pressure on the tub.
    Fit the versatile tap adapters to the bottom of the two taps making use of 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet with the hole in the bath. Make use of the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
    Next off, fit the end of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Ensure you make use of all of the provided washers.
    Connect the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom ought to currently be ready to be suited its final placement.

    Removing Old Taps


    If you require to replace old faucets with new ones as a part of your installment, then the first thing you need to do is detach the water supply. After doing so, switch on the faucets to drain any kind of water remaining in the system. The procedure of removing the existing faucets can be quite troublesome as a result of the restricted accessibility that is typically the instance.
    Utilize a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipelines to the taps. Have a fabric all set for the remaining water that will certainly come from the pipes. As soon as the supply pipelines have been eliminated, make use of the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the solitary taps from turning throughout this procedure. Once the faucets have actually been removed, the holes in the bath/basin will need to be cleansed of any old sealing substance.
    Prior to proceeding to fit the brand-new faucets, compare the pipe links on the old faucets to the new taps. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the new faucets to fit.

    Mounting the Bathtub


    Utilizing both wood boards under its feet, place the bathtub in the required setting. The wood boards are valuable in equally spreading out the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto 4 little points.
    The next objective is to ensure that the tub is leveled all round. This can be accomplished by inspecting the level and also adjusting the feet on the bathtub until the spirit level checks out level.
    To set up taps, fit all-time low of the outermost adaptable faucet adapter to the appropriate supply pipe by making a compression join; then do the exact same for the other tap.
    Turn on the water system and also examine all joints and also brand-new pipework for leakages and tighten them if necessary. Fill the bathtub and also check the overflow outlet and the normal outlet for leaks.
    Finally, fix the bath paneling as described in the manufacturer's instruction manual. Tiling and sealing around the bathtub should wait until the bathtub has actually been utilized at least once as this will resolve it right into its last setting.

    Fitting New Taps


    If the tails of the new taps are plastic, then you will certainly require a plastic adapter to avoid damages to the thread. One end of the connector fits on the plastic tail of the tap and the various other end gives a link to the existing supply pipes.
    If you require to fit a monobloc, after that you will certainly need decreasing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
    Next, position the faucet in the placing opening in the bath/basin guaranteeing that the washers remain in area between the tap and also the sink. Protect the tap in place with the supplier supplied backnut. When the tap is firmly in place, the supply pipes can be attached to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with regular faucet connectors. The previous kind ought to be connected to the faucet ends first, tightening up only by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been connected.

    Tiling Around the Bath tub


    In the area where the bathroom satisfies the tile, it is essential to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to crack a stiff seal, causing the water to pass through the wall between the bathroom and the tiling, bring about complications with wetness as well as feasible leaks to the ceiling listed below.
    You can select from a variety of coloured sealers to blend in your fixtures and also fittings. They are marketed in tubes and cartridges, and also are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to always fill up the bathtub with water prior to securing, to enable the activity experienced when the tub remains in use. The sealer can fracture relatively very early if you do not consider this motion before sealing.
    Conversely, ceramic coving or quadrant tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally easily offered on the marketplace. It is recommended to fit the ceramic tiles making use of water-resistant or water resistant glue and grout.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub Yourself

    Do you enjoy more info about Installing A Bathtub? Try leaving feedback down below. We would be pleased to see your suggestions about this blog post. We are looking forward that you visit us again before long. In case you enjoyed our page if you please be sure to pass it around. I am grateful for your time. Please stop by our blog back soon.



    Book Your Installation

    Leave a Reply

    Your email address will not be published. Required fields are marked *